Maintenance products, accessories en parts for spa, swim spa and infrared sauna

Carefully read the instructions for use on the packaging.

Floculant can be used for cloudy water caused by micro-particles in the water. This product makes these particles larger, they will no longer escape filtration and the spa water will become completely clear again.
Carefully read the instructions for use on the packaging.

Makes dirty water crystal clear again.
Carefully read the instructions for use on the packaging.

Melpool TA plus alkalinityTA plus powder increases the total alkalinity (TA) of the water, which in turn stabilises the pH value. 150 g of this product per 10 m³ of water increases the TA by 10 PPM. Maintain the TA between 100 and 150 PPM. Attention: Do not dose more than 300 g/10 m³ per treatment. Dissolve the powder in a bucket of water and then distribute evenly over the water surface.

The very best water treatment product for your spa. If you choose AquaFinesse, you will enjoy wonderfully clear, clean and incredibly soft spa water every day. You also make an easy-to-use, time-saving and environmentally conscious choice. Everything you need to maintain your spa is in this AquaFinesse package.
Extends the life of your spa components
Provides unprecedented water quality
Provides ultimate convenience
Extremely time-savingContains no hazardous substances
Each set of AquaFinesse lasts between 3 and 6 months depending on the size of your spa.
Carefully read the instructions for use on the packaging.

Test strips for Aquachek Trutester. The pack contains 50 test strips.
Test the water quality of your spa for chlorine, pH, bromine and alkalinity.

Digital meter with 25 test strips
A very easy-to-use test set for measuring chlorine, pH and alkalinity. This photometer works with test strips that you only need to briefly hold in the water. The tester has a memory for the last 9 measurements. Comes with a manual and 25 test strips.

Quick-dissolving stabilised and hydrated disinfectant in granular form. Read the label and product information before use.

Slow-soluble chlorine for regular chlorine dosing.
CAUTION: Do not put directly into the water. Always use a floating chlorine distributor.

Floating chlorine diffuser with adjustable chlorine flow
Size: 23 x 13 x 10 cm
Colour: light blue

Platte afdichtings O-ring voor verwarmingselementWordt veel gebruikt met 2 inch verwarmingsbuizen, zoals Balboa en GeckoMeest voorkomende maatreferentie: 5,08 cm (2 inch)Afmetingen: Ong. dikte: 5mm in totaalDiameter: 75mm (extern)

Verwarmingselement 2,0KW 50HzEnkel geschikt voor spas met IN.yj-2 sturingskasten.Het heat.wav verwarmingselement moet in het retourcircuit van de hoofdpomp (perszijde) worden geînstalleerd.

Verwarmingselement Gecko IN.therm3,8KW, 230 Volt, 50Hz verwarming enkel geschikt voor IN.XM sturingskast.Met ingebouwde Temperatuur als Hi-Limit sensors.Extra drukschakelaar is niet nodig.Afmetingen: Lengte verwarming: 36, 8 cmVerwarmer Hoogte: 12,7 cmDiepte van de verwarming: 11,4 cmRaadplaag een erkend elektircien voor istallatie of contacteer onze technische dienst.Beschikbaar zolang de voorraad strekt

Verwarmingselement, Maddox, 2.5KW, 50HZDit verwarmingselement is niet langer in productie en is beschibaar tot uitputting stock.

Verwarmingselement, Balboa, 2.5KW, 50HzM7 Technologie door het gebruik van een sensor aan beide uiteinden van de verwarmingsset.Afmetingen: Lengte van de verwarming : 38,1 cmVerwarmer Diameter : 5,08 cmTussen de terminals : 3,17 cmTotale lengte compleet : 49,53 cmBeschikbaar zolang de voorraad strekt.

Verwarmingselement, Gecko Mpack, 2,5KW, 50HzGeschikt voor oudere L.A.Spas modellen uitgerust met een Mpack sturingskast van Gecko.Beschikbaar zolang de voorraad strekt.

Verwarmingselement, Gecko SPack, 2,5KW, 50HZGeschikt voor de oudere L.A.Spas modellen uitgerust met Gecko Spack sturingskastBeschikbaar zolang de voorraad strekt.Op bestelling : levertijd van min. 12 weken

Volts: 230 Hz: 50 KW: 3.0 Amps: 11.5 - 12.0
Compatible with: Can be used as a replacement element for Balboa, HydroQuip, Gecko, Thermcore, Aquatemp, RMF, Spa Builders, Brett Aqualine
Connections & Fixings:19mm nut x 2 to secure element in place
Dimensions: Length: 270 mm, Height: 60 mm, Between terminals: 33 mm

Gecko HEAT.WAV 3.0kW Heater IN.XE & New IN.Y Series
230 V, 50 Hz, 3.0 kW, 10.9 Amps
Compatible with: Gecko IN.YE
Connections & Fixings: Heater terminals are connected via flexible power cords that clip directly onto the PCB with no need for tightening bolts etc. This is the exact same heater as 9920-101469
Dimensions: Length: 381 mm, diameter: 50.8 mm, between terminals: 31.75 mm, overall length complete: 495.3mm